Norcold refrigerator · 2 model lines
Norcold refrigerator code 10
Norcold documentation describes 10 separately for each model line: Norcold N3000 series (Thetford troubleshooting codes) (“AC mains supply is out of range”); Norcold N4104 / N4141 / N4150 (“The refrigerator does not work on 120V; check if 120V AC is available and try another power source”). Compare the wording for your model below.
Check your model first. The same code can mean different things on different models. Find the model number on the appliance's data label, then use the matching row below.
What code 10 means by model
| Model line | What the manufacturer says | Source |
|---|---|---|
| Norcold N3000 series (Thetford troubleshooting codes) | The official Thetford N3000 troubleshooting sheet lists error code 10 as: AC mains supply is out of range. | Thetford N3000 Series Troubleshooting Error Codes |
| Norcold N4104 / N4141 / N4150 | The official Norcold N4000 touchscreen owner manual lists code 10 as: The refrigerator does not work on 120V; check if 120V AC is available and try another power source. | Norcold N4104, N4141, and N4150 Installation and Owner Manual |
What you can safely check
- Record the exact display wording and whether an audible alarm is present.
- Turn the refrigerator off if cooling is interrupted or the fault repeats.
- Move perishables if temperature is unsafe.
- Record the exact code, selected source, model, serial number, and whether the code repeats.
- Confirm normal RV shore or generator power is available using owner-visible indicators, then try another source.
Stop and call a technician for
- AC supply, power board, and refrigerator electrical diagnosis should be handled by qualified RV electrical or Thetford/Norcold service.
- AC supply, refrigerator heater, and control diagnosis should be handled by qualified RV electrical or Norcold service.
Do not hand-light, clean burner parts, adjust LP gas, bypass refrigerator controls, or open electrical compartments. Shut off LP if gas odor is present and arrange qualified Norcold service for unresolved faults.
Write this down before you call
- N3000 series model label
- photo of service-mode LED/LCD code
- power source selected
- N4000 touchscreen model and serial label
- photo of display code
- selected source shown on display
Other codes on Norcold N3000 series refrigerators
Full table: Norcold N3000 series refrigerators
- 1 Senses flame when gas should be off
- 2 Burner control module returns incorrect feedback
- 3 Gas lockout because flame fails to ignite within 30 seconds
- 4 DC heater is off when it should be on
- 5 DC heater is on when it should be off
- 6 DC high voltage is out of range
- 7 No engine-run signal is present while control is in Manual DC mode
- 8 AC heater current is measured at 75 percent below nominal current
- 9 AC heater is on when it should be off
- 11 No energy source is available while control is in AUTO mode
- 12 Display board and power board lose communication with each other
- 13 Thermistor fails and the control automatically switches to Backup Operation System
- 18 Code 18 for the start-up display state where all symbols light up briefly before normal o…
Other codes on Norcold N4000 touchscreen refrigerators
Full table: Norcold N4000 touchscreen refrigerators
- 1 If error code 1 is visible, directly contact your dealer or a Norcold Service Center.
- 2 If error code 2 is visible, directly contact your dealer or a Norcold Service Center.
- 3 Code 3 as: The refrigerator does not work on gas; check the bottle and shutoff state, tur…
- 4 If error code 4 is visible, directly contact your dealer or a Norcold Service Center.
- 5 If error code 5 is visible, directly contact your dealer or a Norcold Service Center.
- 6 The refrigerator does not work on 12V; make sure the engine is running and try another po…
- 7 The refrigerator does not work on 12V; make sure the engine is running and try another po…
- 8 If error code 8 is visible, directly contact your dealer or a Norcold Service Center.
- 9 If error code 9 is visible, directly contact your dealer or a Norcold Service Center.
- 11 The refrigerator does not work in AUTO mode; check connected sources and try to run manua…
- 12 If error code 12 is visible, directly contact your dealer or a Norcold Service Center.
- 13 If error code 13 is visible, directly contact your dealer or a Norcold Service Center.
- 18 All symbols on the control panel light up; wait a few seconds until the refrigerator star…