Dometic refrigerator · 1 model line
Dometic refrigerator: Interior lighting is switched on
The Dometic RM8 support page says the interior-lighting fault can be caused by the refrigerator door not being completely closed or being left in parking mode.
What this message means by model
| Model line | What the manufacturer says | Source |
|---|---|---|
| Dometic RM8xxx / RMS8xxx / RML8xxx / RMSL8xxx | The Dometic RM8 support page says the interior-lighting fault can be caused by the refrigerator door not being completely closed or being left in parking mode. | Dometic RM8 Refrigerators Interior Lighting Switched On Support |
What you can safely check
- Make sure the refrigerator door is completely closed.
- Confirm the door is not set to parking mode.
- Record whether the fault continues with the door fully closed.
Stop and call a technician for
- Door switch, latch, lighting circuit, wiring, and refrigerator electronics diagnosis are service-only if the fault repeats with the door closed.
Do not service electrical circuits, wiring, or refrigerator controls; use only normal door and front-panel checks and call qualified service for repeated faults.
Write this down before you call
- Interior data label model, product number, serial number
- Front display code or lamp state photo
- Door position and parking-mode photo if service requests it
Other codes on Dometic RM8 / RMS8 / RML8 refrigerators
Full table: Dometic RM8 / RMS8 / RML8 refrigerators
- 2 + 8 flashing + 20 s beep 230 V mode is not available or the voltage is too low
- 4 + 8 flashing + 20 s beep 12 V mode is not available or the voltage is too low; AES models also call out the D+ sig…
- 3 + 8 flashing + 20 s beep GAS or automatic mode did not ignite the flame
- 15 s beep every two minutes The interior lighting is switched on
- 2 + 7 flashing + 20 s beep The 230 V heating element is defective
- 4 + 7 flashing + 20 s beep The 12 V heating element is defective
- 7 flashing The temperature sensor has no contact or is defective
- 3 + 7 flashing + 20 s beep The burner or cooling unit is defective
- 3 + 8 flashing brightly During internal-battery operation, the flame was not ignited
- 3 + 7 flashing brightly During internal-battery operation, the burner or cooling unit is defective
- internal battery 15 s beep An acoustic signal at 15-second intervals indicates undervoltage detection in the interna…
- external-to-internal power switching failure External-to-internal power switching failure as: Automatic switching from external to int…
- Ground contact, gas valve Ground contact at the gas valve and says to replace the internal batteries that power the…
- Tank stop mode: gas operation blocked 15 minutes Tank stop mode blocks gas operation for 15 minutes.
- Recurring beep A recurring beep can be caused by the refrigerator door not being completely closed or be…
- Undervoltage detection (internal batteries) Undervoltage detection in the internal batteries means the batteries that power the elect…
- Gas operation despite mains supply voltage The refrigerator switches to gas operation when mains supply voltage is too low and will …
- Flame not ignited in GAS/Automatic mode Flame not ignited in GAS or automatic mode can be reset from the front controls and tried…
- AC power not connected or AC voltage < 190 V AC power may not be connected or AC voltage is below the operating threshold; below about…
- 230V not available or voltage too low 230V is not available or voltage is too low; below about 195V the refrigerator stops work…
- 12V not available or voltage too low 12V is not available or voltage is too low and points owners to the 12V connection, on-bo…
- Refrigerator does not function; gas operation not possible although batteries are inserted The on-board power supply was interrupted while gas operation was starting; no automatic …
- DC power not connected DC power is not connected and points owners to the 12V connection, on-board battery, and …
- Flame not ignited in internal power mode Flame not ignited in internal power mode can be reset from the front controls and tried a…
- 230V heating element defective A 230V heating element defective fault can only be repaired by an authorized service prov…
- 12V heating element defective A 12V heating element defective fault can only be repaired by an authorized service provi…
- Flashing + acoustic signal 20 s A flashing display with a 20-second acoustic signal can only be repaired by an authorized…